Model
Standard capacity
Standard voltage
Max voltage
Discharge end voltage
Standard charge current
Max charge current
Max continuous discharge current
Peak discharge
current
Cell dimension
Weight
Life cycle
More
specification
ISR18650 3.7V2500mAh
2500 mAh
3.7 V
4.2 ±0.05 V
2.75 ±0.05 V
0.5C
1C
2C
3C
18x65mm
<48g
>600times
ISR18650 3.7V2600mAh
2600 mAh
3.7 V
4.2 ±0.05 V
2.75 ±0.05 V
0.5C
1C
2C
3C
18x65mm
48g
>800times
ISR18650 3.6V3000mAh
3000 mAh
3.6 V
4.2 ±0.05 V
2.75 ±0.05 V
0.5C
1C
2C
3C
18x65mm
48g
>800times
 
Cell Electric performance
ITEM
CRITERION
TESTING METHOD
Discharge rate performance
A)Discharge Performance (0.2C) ≥100%Rated Capacity
B)Discharge Performance (0.5C) ≥95%Rated Capacity
C)Discharge Performance (1C) ≥90%Rated Capacity 
D)Discharge Performance (2C) ≥80%Rated Capacity 
The cell is charged according to standard charge method, and then, it is discharged to 2.75V using 0.2C current; after, the cell is charged according to standard charge method, and then, it is discharged to 2.75V using 0.5C current; The cell is charged according to standard charge method, and then, it is discharged to 2.75V using 1.0C current; At the end, the cell is charged according to standard charge method, and then, it is discharged to 2.75V using 2.0C current;The discharge capacities under different current shall be recorded.
Cycle life
≥600cycle
Under room temprature, the cell is charged to 4.2V using 0.5C current and then store it for 10 min. Then it is discharged to 2.75V using 1C current. Recycle it continuously till the residual capacity is less than 80% of the rated capacity.
High-Low temperature discharge performance Discharge capacity/ initial capactiy×100% A)60℃≥95% rated capacity 
B)0℃≥80%rated capacity 
C)-10℃≥70% rated capacity
D)-20℃≥55% rated capacity No obvious outside damage, No leakage, No smoke, No explosion
Test the batteries’ initial state and capacity , after standard charging, store it at 60±2℃ for 3 hours, discharge at 0.2C5mA to 2.5V, then make standard charging under room temperature. Then Store it at corresponding constant temperature for 3h under 0±2 ℃/-10±2 ℃/-20±2 ℃ in order. Then discharge the cell at 0.2C5mA to 2.5V and meanwhile make a capacity record. At last store it at room temperature for 2 hours and observe the cell appearance.
Storage performance
Residual Capacity≥90%
Rated Capacity   Recovery Capacity≥98% Rated Capacity Internal resistance increase rate≤30%
After standard fully charge, make standard discharge. This capacity is recorded as initial discharge current. Then the cell is fully charged according to standard charge method and stored at 25℃ for 28 days. After storage, the cell is discharged according to the requirement of standard discharge method. This discharge capacity is named as the Residual capacity. And then charge and discharge the cell by 0.5C. This discharge capacity is recorded as the Recovery capacity.
 
Cell Safety characteristics
ITEM
CRITERION
TESTING METHOD
Overcharge test
No flame、No fire、No explode
The cell is discharged following the standard discharge method. Apply a 10V power supply and a 3C charge current for 1.5hrs.
130℃ hot oven test
When the temperature of the cell is 130℃. Cell must not fire or explode in 30 minutes
The cell is charged following the standard charge method. After charging the cell is put in the oven. And then the oven temperature will be ramped at 5℃ per minute to 130℃ and held at 130℃.  When the temperature of the cell reach 130℃, the cell is maintained in the 130℃ oven for a maximum of 30 minutes or until a fire or explosion is obtained.
Over discharge test
No flame、No fire、No explode
Cell shall first be charged according to standard charge method,and then cell is to be discharged by 0.2C current for 12 hours; The test is completed when the cell is to be discharged up to 250% of rate capacity or the other protective devices prevent the discharge.
Crush test
No fire、No explode
After charging a cell following the standard charge method, the cell shall be crushed between two flat surfaces. The direction of the crushing force shall be vertical to axis of the cylinder. The crushing force is to be applied by a hydraulic ram with a 32mm diameter piston. Crushing force is approximately 13 KN. Once the maximum pressure has been obtained it is to be released.

 

         
Popular models
Electric bike battery 24V10Ah
 
Electric scooter battery 36V20Ah
 
Lithium ion cell 18650 3.7V2500mAh
Contact us
Electric bike battery 24V13Ah
 
Electric scooter battery 48V20Ah
 
Lithium ion cell 18650 3.7V2600mAh
SINC BATTERY
Electric bike battery 24V30Ah
 
Electric scooter battery 48V30Ah
  Lithium ion cell 18650 3.6V3000mAh
Address: At the 275-km spot to No.102 national road south,Economic-Technological Development Zone,qinhuangdao,China.
Electric bike battery 36V10Ah
 
Electric scooter battery 48V40Ah
  Lifepo4 cell 21700 3.2v3000mah
Electric bike battery 36V13Ah
 
Electric scooter battery 60V20Ah
  Lithium ion cell 21700 3.6v4000mah
Electric bike battery 36V15Ah
 
Electric scooter battery 60V30Ah
 
Lithium ion cell 21700 3.6v4500mah
Electric bike battery 48V10Ah
 
Electric motorcycle battery 60V20Ah
 
Charger 24V2A,3A,4A,5A
Electric bike battery 48V13Ah
 
Electric motorcycle battery 72V20Ah
 
Charger 36V2A,3A,4A,5A
Inquire email
Electric bike battery 48V15Ah
 
Electric motorcycle battery 72V28Ah
 
Charger 48V2A,3A,4A,5A
xinchibatterysales@gmail.com
Electric bike battery 48V20Ah
 
Electric motorcycle battery 72V33Ah
 
Charger 60V2A,3A,72V2A,3A
All inquire will be reply within 48 hours
Lithium ion battery BMS 24V,36V,48V,60V,72V  
Electric motorcycle battery 72V40Ah
 
 
All rights reserved by SINCBATTERY Copy right © Email: xinchibatterysales@gmail.com